Show logfile
Automated smoke report for branch blead 5.35.12 patch 300ff263fbad8007ca52d84a8be8b98fba791a3c v5.35.11-140-g300ff263fb
cjg-alpine3: Intel(R) Xeon(R) CPU E5-2620 v2 @ 2.10GHz (GenuineIntel 2098MHz) (x86_64/1 cpus)
    on        linux 5.15.37-0-lts [Alpine Linux v3.15 3.15.4]
    using     gcc version 10.3.1 20211027 (*1)
    smoketime 8 hours 25 minutes (average 42 minutes 9 seconds)

Summary: FAIL(F)

O = OK  F = Failure(s), extended report at the bottom
X = Failure(s) under TEST but not under harness
? = still running or test results not (yet) available
Build failures during:       - = unknown or N/A
c = Configure, m = make, M = make (after miniperl), t = make test-prep

v5.35.11-140-g300ff263fb
---------------------- ----------------------------------------------------
F  F                    -Dcc=gcc (*1)
F  F                    -Dcc=gcc -Duse64bitall (*1)
F  F                    -Dcc=gcc -Duselongdouble (*1)
F  F                    -Dcc=gcc -Duseithreads (*1)
F  F                    -Dcc=gcc -Duseithreads -Duse64bitall (*1)
F  F                    -Dcc=gcc -Duseithreads -Duselongdouble (*1)
|  |
|  +------------------  stdio DEBUGGING
+---------------------  stdio

Applied patches:

Skipped tests:
      # One test name on a line

Test failures:
~~ ../t/porting/podcheck.t ..................................... FAILED 193-194
  [stdio] -Dcc=gcc -Duse64bitall
  [stdio] -Dcc=gcc -Duselongdouble DEBUGGING
  [stdio] -Dcc=gcc -Duseithreads -Duse64bitall DEBUGGING
  [stdio] -Dcc=gcc -Duse64bitall DEBUGGING
  [stdio] -Dcc=gcc -Duseithreads
  [stdio] -Dcc=gcc -Duseithreads -Duselongdouble DEBUGGING
  [stdio] -Dcc=gcc DEBUGGING
  [stdio] -Dcc=gcc -Duseithreads -Duse64bitall
  [stdio] -Dcc=gcc -Duseithreads DEBUGGING
  [stdio] -Dcc=gcc -Duselongdouble
  [stdio] -Dcc=gcc -Duseithreads -Duselongdouble
~~ ../t/porting/regen.t ........................................ FAILED 22 Non-zero exit status: 255 Bad plan.  You planned 42 tests but ran 22.
  [stdio] -Dcc=gcc -Duseithreads -Duse64bitall DEBUGGING
  [stdio] -Dcc=gcc -Duselongdouble DEBUGGING
  [stdio] -Dcc=gcc -Duse64bitall
  [stdio] -Dcc=gcc -Duseithreads DEBUGGING
  [stdio] -Dcc=gcc -Duseithreads -Duse64bitall
  [stdio] -Dcc=gcc -Duselongdouble
  [stdio] -Dcc=gcc -Duseithreads -Duselongdouble
  [stdio] -Dcc=gcc -Duse64bitall DEBUGGING
  [stdio] -Dcc=gcc
  [stdio] -Dcc=gcc -Duseithreads
  [stdio] -Dcc=gcc -Duseithreads -Duselongdouble DEBUGGING
  [stdio] -Dcc=gcc DEBUGGING

Test todo-passed:

MANIFEST messages:
  MANIFEST did not declare '.mailmap'

Compiler messages:
  Makefile:258: warning: ignoring prerequisites on suffix rule definition
  Makefile:254: warning: ignoring prerequisites on suffix rule definition
  makefile:258: warning: ignoring prerequisites on suffix rule definition
  makefile:254: warning: ignoring prerequisites on suffix rule definition

About this smoke:
    smoking-perl: 5.30.2
  smoker-version: 1.71/0.046
       timestamp: 2022-05-08 22:12:41+00
          tester: core

-- 
Report generated by Test::Smoke::Gateway v0.10